Mercurial > whatever / changeset

--- a/content/hp8662a.rst	Wed Apr 11 23:17:04 2018 +0200
+++ b/content/hp8662a.rst	Wed Apr 11 23:11:52 2018 +0200
@@ -42,6 +42,7 @@
 before even attempting to fix the PSU.
 
 .. image:: {filename}images/hp8662a/dirty_hp.jpg
+   :class: image-process-large-photo
 
 
 And I must say that if most of the unit is very easy to service due to the
@@ -51,14 +52,18 @@
 so very tedious.
 
 .. image:: {filename}images/hp8662a/top_before_2.jpg
+   :class: image-process-large-photo
 
 .. image:: {filename}images/hp8662a/bottom_before.jpg
+   :class: image-process-large-photo
 
 .. image:: {filename}images/hp8662a/front_after.jpg
+   :class: image-process-large-photo
 
 Also, there are hundreds of screws in this unit! it's insane.
 
 .. image:: {filename}images/hp8662a/top_after.jpg
+   :class: image-process-large-photo
 
 Whatever, I finally got to a point I could clean most of the parts of the unit,
 so I started to reassemble it. Unfortunately, I did not took enough pictures
@@ -66,12 +71,14 @@
 like an HP 8662A...
 
 .. image:: {filename}images/hp8662a/reassembling_2.jpg
+   :class: image-process-large-photo
 
 Once I had the structure of the generator back togother, with the back plane in
 place but no other board nor module plugged in, I started to take care of the
 PSU.
 
 .. image:: {filename}images/hp8662a/reassembling_1.jpg
+   :class: image-process-large-photo
 
 The PSU
 =======
@@ -87,6 +94,7 @@
   the mani switch on the front panel only activate the switching.
 
 .. image:: {filename}images/hp8662a/PSU_simplified_schematic.jpeg
+   :class: image-process-large-photo
 
 The 4 boards the PSU is made of are:
 
@@ -106,6 +114,7 @@
   regulation being made on the 5.2V rail, which is not regulated by A7A1.
 
 .. image:: {filename}images/hp8662a/PSU_block_diagram.jpeg
+   :class: image-process-large-photo
 
 So I gave a close look at thes boards, beginning by the main board, the I found
 the culprit for the smoke: the input protection thermistor. Strangely, it still
@@ -138,6 +147,7 @@
 the inverter board were very low. Somethin was wrong.
 
 .. image:: {filename}images/hp8662a/PSU_inverter_schematic.jpeg
+   :class: image-process-large-photo
 
 Looking at the schematics and the boards, I did find several failure points:
 
@@ -160,6 +170,7 @@
   skookum but does the job for a few cents.
 
 .. image:: {filename}images/hp8662a/broken_choke.jpg
+   :class: image-process-large-photo
 
 After these fixes, I reassembled the PSU and tried again: the result was quite
 promising, but not a complete success: the PSU seemed to start, but very

--- a/pelicanconf.py	Wed Apr 11 23:17:04 2018 +0200
+++ b/pelicanconf.py	Wed Apr 11 23:11:52 2018 +0200
@@ -10,6 +10,7 @@
 TWITTER_USERNAME = u'douardda'
 CONTACTS = (('twitter', 'https://twitter.com/twttrAcc'),)
 
+
 if _isprod:
     SITEURL = 'https://whatever.sdfa3.org'
     PIWIK = '''
@@ -80,9 +81,31 @@
            'pelican_dailymotion',
            'pelican_javascript',
            'wavedrom',
+           'image_process',
            ]
 RESPONSIVE_IMAGES = True
 TYPOGRIPFY = True
 SINGLE_AUTHOR = True
 MINT = True
 SITEMAP = {'format': 'xml'}
+
+IMAGE_PROCESS = {
+  'crisp': {'type': 'responsive-image',
+            'srcset': [('1x', ['scale_in 800 600 True']),
+                       ('2x', ['scale_in 1600 1200 True']),
+                       ('3x', ['scale_in 3200 2400 True']),
+                       ],
+            'default': '1x',
+            },
+  'large-photo': {'type': 'responsive-image',
+                  'sizes': '(min-width: 1200px) 800px, (min-width: 992px) 650px, \
+                            (min-width: 768px) 718px, 100vw',
+                  'srcset': [('600w', ["scale_in 600 450 True"]),
+                             ('800w', ["scale_in 800 600 True"]),
+                             ('1600w', ["scale_in 1600 1200 True"]),
+                             ],
+                  'default': '800w',
+                  },
+  }
+
+