55 power supply. |
55 power supply. |
56 |
56 |
57 .. image:: {static}/images/lambda/lpd422fm_board1.jpg |
57 .. image:: {static}/images/lambda/lpd422fm_board1.jpg |
58 :alt: Bottom view of one regulator of the LPD 422 FM dual regulated |
58 :alt: Bottom view of one regulator of the LPD 422 FM dual regulated |
59 power supply. |
59 power supply. |
60 |
60 |
61 The component, especially the big caps, looks like original parts and |
61 The component, especially the big caps, looks like original parts and |
62 the PCB is a bit burnt by the small power transistor, but nothing too |
62 the PCB is a bit burnt by the small power transistor, but nothing too |
63 scary. |
63 scary. |
64 |
64 |
65 The power supply works nice. No smoky or smelly behaviour on load, and |
65 The power supply works nice. No smoky or smelly behaviour on load, and |
75 - `Instruction and Service Manual for Lambda LPD suffix A Series Power |
75 - `Instruction and Service Manual for Lambda LPD suffix A Series Power |
76 Supplies <{static}/pdfs/lambda/LambdaLPD.pdf>`_: this is not |
76 Supplies <{static}/pdfs/lambda/LambdaLPD.pdf>`_: this is not |
77 exactly the same model, but it really very close. |
77 exactly the same model, but it really very close. |
78 |
78 |
79 |
79 |
80 |
80 |
81 Quick mesurements |
81 Quick mesurements |
82 ================= |
82 ================= |
83 |
83 |
84 In these quick measurements, I've not used the voltage remote sensing |
84 In these quick measurements, I've not used the voltage remote sensing |
85 of the power supply. |
85 of the power supply. |
86 |
86 |
87 First, a view of the noise at the output of the PSU; 0V, no load: |
87 First, a view of the noise at the output of the PSU; 0V, no load: |
88 |
88 |
89 .. image:: {static}/images/lambda/DS1Z_QuickPrint2.png |
89 .. image:: {static}/images/lambda/DS1Z_QuickPrint2.png |
90 :alt: Noise level of the LPD422FM - 0V/0A |
90 :alt: Noise level of the LPD422FM - 0V/0A |
91 |
91 |
92 Same at 20V, no load: |
92 Same at 20V, no load: |
93 |
93 |
94 .. image:: {static}/images/lambda/DS1Z_QuickPrint3.png |
94 .. image:: {static}/images/lambda/DS1Z_QuickPrint3.png |
95 :alt: Noise level of the LPD422FM - 20V/0A |
95 :alt: Noise level of the LPD422FM - 20V/0A |
96 |
96 |
97 And at maximum voltage (40V, no load): |
97 And at maximum voltage (40V, no load): |
98 |
98 |
99 .. image:: {static}/images/lambda/DS1Z_QuickPrint4.png |
99 .. image:: {static}/images/lambda/DS1Z_QuickPrint4.png |
100 :alt: Noise level of the LPD422FM - 40V/0A |
100 :alt: Noise level of the LPD422FM - 40V/0A |
101 |
101 |
102 Then, with the `ZPB30A1 electronic load <{static}/ZPB30A1.rst>` |
102 Then, with the `ZPB30A1 electronic load <{filename}/ZPB30A1.rst>` |
103 connected but not consuming any current (20V, 0A): |
103 connected but not consuming any current (20V, 0A): |
104 |
104 |
105 .. image:: {static}/images/lambda/DS1Z_QuickPrint5.png |
105 .. image:: {static}/images/lambda/DS1Z_QuickPrint5.png |
106 :alt: Noise level of the LPD422FM connected to the ZPB30A1 - 20V/0A |
106 :alt: Noise level of the LPD422FM connected to the ZPB30A1 - 20V/0A |
107 |
107 |
153 I also plan to replace the banana jacks on the front panel (their |
153 I also plan to replace the banana jacks on the front panel (their |
154 barrels are very short, less than 1cm: I cannot plug a standard banana |
154 barrels are very short, less than 1cm: I cannot plug a standard banana |
155 plug more than half its lenght). I may also try to bring the remote |
155 plug more than half its lenght). I may also try to bring the remote |
156 sensor plugs on the front panel (with a pair of easy to set or remove |
156 sensor plugs on the front panel (with a pair of easy to set or remove |
157 jumps): I like to have the sense terminals ready to use. |
157 jumps): I like to have the sense terminals ready to use. |
158 |
|