changelog
- Thu, 12 Nov 2020 20:26:35 +0100
- by David Douard <david.douard@sdf3.org> [Thu, 12 Nov 2020 20:26:35 +0100] rev 53
- Reorganize the display + improvements for dimmed flags
- the whole upper zone is now dediacated to the main character line
- make sure eash flag has a dedicated non-overlaping area
- improve support for dimmed flags (not yet properly functionning since this
dimm state is actually stateful, so some major refactorings are needed to
properly handle this).
- Tue, 10 Nov 2020 22:24:03 +0100
- by David Douard <david.douard@sdf3.org> [Tue, 10 Nov 2020 22:24:03 +0100] rev 52
- Add support for 0x08 and 0x09 command codes (display a flag dimm/bright)
- Tue, 10 Nov 2020 22:22:16 +0100
- by David Douard <david.douard@sdf3.org> [Tue, 10 Nov 2020 22:22:16 +0100] rev 51
- Add support for dimmed flag display
- Tue, 10 Nov 2020 22:21:35 +0100
- by David Douard <david.douard@sdf3.org> [Tue, 10 Nov 2020 22:21:35 +0100] rev 50
- Remove now dead/useless code
- Mon, 09 Nov 2020 23:05:24 +0100
- by David Douard <david.douard@sdf3.org> [Mon, 09 Nov 2020 23:05:24 +0100] rev 49
- Refactor HPSerial to get rid of packet collision misbehavior
completely split the key sending code from the irq-based receiveing logic.
When sending keycodes, disable the RxIrq callback and handle send and recv
of bytes synchronously.
The keycode sending routine rus in a dedicated thread.
- Sat, 07 Nov 2020 19:24:11 +0100
- by David Douard <david.douard@sdf3.org> [Sat, 07 Nov 2020 19:24:11 +0100] rev 48
- Remove print statements
- Sat, 07 Nov 2020 19:23:21 +0100
- by David Douard <david.douard@sdf3.org> [Sat, 07 Nov 2020 19:23:21 +0100] rev 47
- Attempt to improve the detection of packet collisions (not fixed yet)
- Sat, 07 Nov 2020 19:22:04 +0100
- by David Douard <david.douard@sdf3.org> [Sat, 07 Nov 2020 19:22:04 +0100] rev 46
- Fix display of flags and improve dimm char handling
- Sat, 07 Nov 2020 19:20:39 +0100
- by David Douard <david.douard@sdf3.org> [Sat, 07 Nov 2020 19:20:39 +0100] rev 45
- Adjust font rendering
- fix +, -, and ' ' so they habe the same width
- add a method to move the current location for a given char (without drawing it)
- Sun, 01 Nov 2020 22:21:19 +0100
- by David Douard <david.douard@sdf3.org> [Sun, 01 Nov 2020 22:21:19 +0100] rev 44
- Many improvements
- add support for dimm-based selection,
- add support for poweroff (at least power thr display off),
- add support for the initial key pressed during initialization sequence,
- fix a race condition (sending a keycode while receiving a message)
- add support for the shift button
- many code cleanups and improvements
- Sun, 01 Nov 2020 22:16:33 +0100
- by David Douard <david.douard@sdf3.org> [Sun, 01 Nov 2020 22:16:33 +0100] rev 43
- Add a series of reference serial data sessions from a working 34970A unit.
These sessions do have a few glitches, however (random off by one bit,
probably due to a sampling freq a bit too low).
Comes with an adapted version of the uart_filter.py script to interpret the
communication protocol.
- Sun, 01 Nov 2020 22:13:03 +0100
- by David Douard <david.douard@sdf3.org> [Sun, 01 Nov 2020 22:13:03 +0100] rev 42
- fox the example sigrock-cli cmd line for reading serial session from the dslogic
- Sun, 01 Nov 2020 22:11:39 +0100
- by David Douard <david.douard@sdf3.org> [Sun, 01 Nov 2020 22:11:39 +0100] rev 41
- rename fp environment as fp_dfu and add a fp_stlink
to make it a bit easier to choose the selected upload protocol
- Sun, 01 Nov 2020 22:10:10 +0100
- by David Douard <david.douard@sdf3.org> [Sun, 01 Nov 2020 22:10:10 +0100] rev 40
- SSD1322: add power off/on methods
- Tue, 27 Oct 2020 21:48:28 +0100
- by David Douard <david.douard@sdf3.org> [Tue, 27 Oct 2020 21:48:28 +0100] rev 39
- hp34comm: add support for boot keycode
- Mon, 26 Oct 2020 00:23:55 +0100
- by David Douard <david.douard@sdf3.org> [Mon, 26 Oct 2020 00:23:55 +0100] rev 38
- kill tabs (again) in src/main.cpp
- Mon, 26 Oct 2020 00:16:13 +0100
- by David Douard <david.douard@sdf3.org> [Mon, 26 Oct 2020 00:16:13 +0100] rev 37
- Extracted the display related functions in a Display class
- Sun, 25 Oct 2020 23:00:17 +0100
- by David Douard <david.douard@sdf3.org> [Sun, 25 Oct 2020 23:00:17 +0100] rev 36
- Add support for the shift flag
- Sun, 25 Oct 2020 22:45:24 +0100
- by David Douard <david.douard@sdf3.org> [Sun, 25 Oct 2020 22:45:24 +0100] rev 35
- Indent src/main.cpp with 2-ws
- Sun, 25 Oct 2020 22:17:15 +0100
- by David Douard <david.douard@sdf3.org> [Sun, 25 Oct 2020 22:17:15 +0100] rev 34
- Add a key mapping table (protocol value vs. raw keycode) and send it
Also reformat the file for 2-wspace-tabs
- Sun, 25 Oct 2020 22:15:35 +0100
- by David Douard <david.douard@sdf3.org> [Sun, 25 Oct 2020 22:15:35 +0100] rev 33
- Reformat Keypad.cpp
- Sun, 25 Oct 2020 22:15:03 +0100
- by David Douard <david.douard@sdf3.org> [Sun, 25 Oct 2020 22:15:03 +0100] rev 32
- Update the main code: extract headers and use a CircularBuffer for key events
Also fix some forgotten s/_FP_F303RE/_FP_F030RD/
- Sun, 25 Oct 2020 17:12:22 +0100
- by David Douard <david.douard@sdf3.org> [Sun, 25 Oct 2020 17:12:22 +0100] rev 31
- Add a few patterns in hgignore
- Sun, 25 Oct 2020 17:02:53 +0100
- by David Douard <david.douard@sdf3.org> [Sun, 25 Oct 2020 17:02:53 +0100] rev 30
- Update the custom target HP34970_FP_303RD
update the platformio.ini:
remove unused flags, and configure so it uses includes from the project's root
directory (in TARGET_HP34970_FP_F303RD) so these .h/.c files do not conflict
when compiling for other targets.
Add a TARGET_HP34970_FR_F303RD/ for target specific headers/linker files.
Add a src/TARGET_HP34970_FR_F303RD/ for c files (protected by '#if defined'
statments).
- Sun, 25 Oct 2020 16:58:38 +0100
- by David Douard <david.douard@sdf3.org> [Sun, 25 Oct 2020 16:58:38 +0100] rev 29
- Set custom_config for the F303RD
- remove "supported_form_factors": irrelevant
- rename as HP34970_FP_F303RD
- enforce HSE_XTAL clock source
- add USBDEVICE flag in device_had_add
- set ROM size to 384ko
- Fri, 16 Oct 2020 22:08:47 +0200
- by David Douard <david.douard@sdfa3.org> [Fri, 16 Oct 2020 22:08:47 +0200] rev 28
- compile for nucleo f446re & f303re with mbed 6
- Thu, 15 Oct 2020 01:12:31 +0200
- by David Douard <david.douard@sdfa3.org> [Thu, 15 Oct 2020 01:12:31 +0200] rev 27
- add QEI
- Thu, 15 Oct 2020 01:11:03 +0200
- by David Douard <david.douard@sdfa3.org> [Thu, 15 Oct 2020 01:11:03 +0200] rev 26
- Several stuff
- Sun, 30 Aug 2020 22:53:15 +0200
- by David Douard <david.douard@sdfa3.org> [Sun, 30 Aug 2020 22:53:15 +0200] rev 25
- Add .pio to hgignore
- Mon, 28 Jan 2019 21:51:45 +0100
- by David Douard <david.douard@logilab.fr> [Mon, 28 Jan 2019 21:51:45 +0100] rev 24
- Add the (missing?) Keypad lib
- Mon, 28 Jan 2019 21:50:09 +0100
- by David Douard <david.douard@logilab.fr> [Mon, 28 Jan 2019 21:50:09 +0100] rev 23
- Add the serialdata tool
to read and decode serial data from the hp34970 using the dslogic.
- Wed, 07 Nov 2018 20:00:52 +0100
- by David Douard <david.douard@logilab.fr> [Wed, 07 Nov 2018 20:00:52 +0100] rev 22
- more stuff
